|English Français Español Deutsch Italiano Português 日本語 Русский Nederlands العربية Norsk Dansk Svenska 한국어 Suomi עברית Türkçe Polski Čeština Ελληνικά Hrvatski Română Magyar|
Product came fully assembled which was a good surprise. Delivery was on time but the processing took a full week. Still working on the installation but the product seems to be in good condition. The tube came with a couple couplings which I think are meant for use if you do not properly run your tube back to the extruder screw. The E3D V6 seems to be a far beefy product and required some removal of the existing fan shrouds and a little bit of drilling to get the tube to fit through the extruder case properly on my Robo 3D. I recycled the connectors from my broken hot end that came with the Robo 3D rather than running the wired all the way back to the control board. I attached a picture to show the difference in size between my broken hot end and the new E3D V6.
O produto chego antes do esperado e em excelentes condições, tudo conforme o esperado!
Obrigada por comprar conosco. Sempre estaremos trabalhando para a melhoria da qualidade de nossos produtos e para melhor assistência a todos os clientes que escolheram nosso site
по cintia_remote 21.2.2017
Product conform to description, well packaged.
excelente producto, buena calidad y envio rapido.
Gracias por comprar con nosotros. Siempre trabajamos en la mejora de la calidad de los productos y para proporcionar un mejor servicio a todos los clientes que eligen nuestro sitio.
по fabio1_remote 4.9.2016
Received the purchased E3d V6 Hot End well packed and within a few days.
Everythign was assambled, cables are long enough.
emballage parfait livraison dans le temps promis.
aspect du produit correct sera tester bientôt
Thank you for your kind support. We are really glad that you are satisfied with our products and services. We hope we can serve you even better next time!
по liu liu 10.3.2016
Wie erwartet sehr gute Qualität. Für den Preis unschlagbar.
Habe mir gleich noch einen als Ersatz bestellt.
Thank you for your support. We are really happy that you are satisfied with our products and services. We hope to serve you better next time!
по liu liu 11.2.2016
Received well in time, all parts are there.
First off, this is NOT an E3DV6. It is a clone, obviously. The measurements are different from the standard. This will affect whatever brackets you decide to print out to help with your install. The collar is larger than the real one, and your model will need to be adjusted to compensate.
The unit did indeed come fully assembled, and I quickly disassembled it. I intended to use my original heater core, thermistor, and fan. I drilled the thermistor hole just a tad to allow my own, with a larger glass bead, to fit. I strongly recommend that you add your own insulation to the thermistor wires right at the heater block to avoid grounding out the wires when you screw down the set screw. It needs to be known, there is an internal PTFE tube in the *lower* end of the heatbreak, so you still can't go over 250c without disassembling it and removing that.
After I reassembled the unit with all of my own parts, and a custom fan shroud for my larger fan, I installed it in my XYZ Davinici Pro, and it worked just fine. I did have to fiddle with the thermistor a bit to keep it from faulting out. That's when I learned that the screw will cut through the wire insulation and ground the wires if you screw it down too tight. Don't do that. Also, be sure to heat the unit to operating temperature, without filament, and give the nozzle one last tightening. Not too much, but it should seat a bit more once it's hot. Then you won't have leaks when you start running plastic.
I'm happy with the quality so far.
Funziona benissimo e mi ritengo molto soddisfatto per la Vostra serietà e per la velocità della spedizione ma non per la spesa aggiuntiva dovuta alla Dogana
A cosa serve? Non capisco la descrizione!! Traduzione da cani
по colombara.a 31.10.2016