top banner
ziqiao elm327 usb v1.5 obd2 자동차 진단 인터페이스 스캐너 elm 327 v1.5 obdii 진단 도구 #7195054
5 3 리뷰 91 판매
USD $16.79 USD $22.79
27% 할인
ziqiao elm327 usb v1.5 obd2 자동차 진단 인터페이스 스캐너 elm 327 v1.5 obdii 진단 도구
$ 16.79
할인
할인
무료 배송
할인
더 보기
수량:
제품을 선택하시면 제작 소요 시간이 계산되어 질것입니다.
배송 시간: 긴급 빠른 배송 4-7 영업일 기준

저작권 위반 지침

참고 사항 :

주문 제작을 위한 사진을 선택하실 때 저작권 침해를 위반 하지 않는지 확인하시고 만일 저작권 침해 사항에 문제에 대해 저희는 책임을 지지 않습니다. 이용 약관에 동의하시는지 확인하시고 만일 추가 질문이 없으신 경우 확인을 클릭하시기 바랍니다. 저희와 함께 쇼핑해 주셔서 다시 한번 감사드립니다.

이용 약관에 동의하는지 확인하시기 바랍니다.

브랜드:ZIQIAO

Brand Introduction: No branding required

사진들

OBD2 Interface:16pin . without FT232RL Chip . only wok with PC . langauge:English . Software Version:V2.1 Hardware version:V1.5 Compatible systems: Software support platform: Windows XP, Windows 7/8. Compatible software: Window: ScanMaster-ELM, ScanTool.net, PCMSCAN ELM, etc. ELM327 USB V1.5 car diagnostics Interface Scanner Technical Specification: ELM327 Based - Datasheet OBDII Plug: J1962 16-Pin Male (to Car) USB Port : (to Computer or PDA) High quality UL certified USB Cable (equivalent to CE). CAN (ISO 15765-4) ISO 9141-2 ISO 14230-4 Automatically searches for the correct protocol or can be configured manually. USB Port Serial Interface uses AT commands to look like a modem. Status LED Length with USB Lead : 1.5 metres What's New for elm327 plastic v1.5 General Items: RS232 baud rates to 500 Kbps Adaptive Timing automatically adjusts ST timeouts Power up to AT MA is selectable Source (tester) address can be changed Can reset all PPs with a jumper Receive addresses can be independently set Power Control with a low power standby mode A 4800 baud ISO option A non-volatile memory location for storing user data CAN extended addressing support You can now perform ISO/KWP bus initializations without having to send a request An SS command allows searching through the OBD protocols sequentially A new TA command allows the Tester Address to be easily changed Factory calibration for the voltage reading circuit can be easily restored ISO 9141 and ISO 14230: The slow initiation address can now be varied Control over key word checking KWP protocols can now transmit 3 or 4 byte headers CAN: New J1939 protocol Two user-definable CAN protocols Improved error handling and recovery Extended addressing support How To Use USB ELM327: 1. Turn the car's ignition switch ON. No need to start the engine. 2. Start the software program, click "Options", select the correct communications port. 3. Your interface now works! Make sure the software can reliably access all the control modules that it should in your car. elm327 usb obd2 obdii scanner Features: Support 64 bit system Read and erase diagnostic trouble codes (DTCs) and turn off the check engine light Compatible with Systems: DOS, Windows View real-time vehicle data, graphs and performance parameters while you're driving Find and fix problems before they happen Compatible with all OBDII compliant vehicles Clear diagnostic trouble codes and turn off check engine lights Display and record real-time sensor data, including: Vehicle Speed RPM Fuel Consumption Engine Coolant Temp Fuel Pressure Calculated Engine Load Throttle Position Intake Manifold Pressure Air Intake Temp Timing Advance Mass Air Flow Fuel Level Barometric Pressure Fuel Trim + More Note : Your vehicle may not support all engine metrics. The availability of engine metrics varies depending on the vehicle make and model ELM327 USB OBD2 Auto Car diagnostic scanner tool Compatible Protocols: ISO15765-4 (CAN) ISO14230-4 (KWP2000) ISO9141-2 J1850VPW J1850PWM

Q:What's the version of this unit? A:It's V1.5 version of this unit Q:What's the difference for the Version V1.5 and V2.1? A:The V1.5 version can do much more car models than V2.1 one. Q.What's the Password of the Bluetooth? A:1234 Q:If it can do all most car models and diesel car models? A:No,it can just support most standard OBD II car models,Diesel car models can't be supported Q:Which android system phone can compatible? If it can compatible with Iphone? A:Please kindly use Android V4.0-4.4 .The Iphone can't be supported Q:Why my computer can't connect with this Bluetooth? A:This unit is with V2.0 version Bluetooth, check your computer if it's V2.0 version,or please use V2.0 bluetooth adapter Q:Why my phone can't connect with the Bluetooth? A:Please kindly check if you choose the bluetooth connect way in software setting Q:My phone can connect with the unit,but it can't find my car? A:1.please check if you choose the"OBD II" adapter of "adapter choice"in setting software. 2.check if your android system version is V4.0-4.4 . 3.check the protocol of this car if it can be supported, and try with more new car.

저작권 침해 신고

저작권 침해 신고

성공적으로 제출되었습니다!

제출해 주셔서 감사합니다!가능한 빠른 시일내에 처리하겠습니다

장바구니에 새 제품이 추가되었습니다.
나의 장바구니 보기
다른 인기 있는 제품
ATest